Thank you for choosing IJOY! Please read this manual carefully to ensure proper use. For additional information regarding this product or its use, please consult your local UOY retailer or visit our website www.ijoycig.com
Product Introduction:
IJOY Diamond mini is a cool and stylish dual 18650 BOX MOD. Its design is inspired by the diamond multi-faceted cutting technology. The fire button also adopts diamond design, which fits with the design elements of the whole machine. Millisecond fire speed, large OLED display, 225W high power, easy operation, various modes selectable, support NI, Tl, 55 temperature control, support for large size atomizer, support USB charging, and firmware upgradeable!
Parameter
1* IJOY Diamond Mini Box Mod (225w) 1 * USB Cable
1 * Manual 1 * Warranty Card
Specifications
• Screen size: 0.96″0LED.
• Size: 87.3*46.3*32.1mm /3.43*1.82*1.28 inches.
• Output Wattage: 5watts-225watts
• Output Voltage: 1Volts-8.0Volts.
• Output Current: 1.0A-40A.
• Temperature Range: 300-600’℉/ 150-315℃
• Wattage control mode wire Resistance Range:0.05ohm-3.0ohm
• Power efficiency: 95%.
• Fire method: Stainless steel metal stretch button.
• Adjust power method: up and down button.
• Upgradable firmware: YES.
• Output mode·VW/TI/Nl/55 and special USER Mode
IJOY Diamond Mini Kit Operation Instruction:
1. Power On/off
Press the fire button 5 times in quick succession to turn the device on and off. After switch on, OLED display DIAMOND logo and software version number at stand by mode.
(Note:
Please adjust the wattage to a proper range to match the atomizer you used before using.
2.Vaping
While the device is power on, just keep pressing the fire button to vape
(Firing timeout: 10 Seconds)
While the device is power on, the OLED screen default display VW Mode.
3. General Functions Enter Into The Main Menu
Press the fire button 3 times to enter into the main menu. Press the right and left regulatory buttons to switch among different functions. Press the fire button to confirm.
4. Power Mode
In the main menu, switch to “P” setting, press fire button to confirm. Press right and left buttons to adjust the wattage.
Intensity Setting In Power Mode
In the main menu, switch to intensity setting, press fire button to confirm Press right and left buttons to switch among below4 modes. In user mode, press fire button to switch among each setting columns. Press right and left
buttons to adjust the wattage After setup is completed, press fire button to switch to “EXIT”. Press right or left button to confirm.
Norm Mode: Maintains the currently set power.
Hard Mode: 30% higher than the currently set power.
Soft Mode: 20% lower than the currently set power.
User Mode. Customize the power output for the first three seconds of each puff, with each setting column representing half a second.
5. Temp Mode
Ni/ Ti /SS/TCRM1/TCRM2
In the main menu, switch to ”T” setting, press fire button to confirm. Press right and left buttons to switch among Ni/Ti/SS/Ml/M2 modes. Press fire button to confirm. Press right button, when “W” flashing, press right and left buttons to adjust wattage. Press left button, when”°F” or”℃” flashing, press right and left buttons to adjust temperature value.
The temperature unit will cycle between ° F and °C when the minimum or maximum temperature is reached.
In the temperature control mode to replace the heating wire, the first let Heating wire in the indoor temperature, after installed the heating wire, The screen will appear the heating wire resistance, Figure 1 is the heating wire Of the initial value, if the “resistance” is very accurate directly Use, if not very accurate then need to correct the heating wire Of the resistance.
6. TCR Mode (M1, M2)
With the TCR (Temperature Coefficient of Resistance) function available now, you can customize your temperature control coiIs (Ni, Ti, SS) on your own. In the main menu, switch to ‘T” setting, press fire button to confirm. Switch to Ml/M2 modes. Press fire button to confirm.
How to set the TCR?
In the main menu, switch to TCR mode indication, press fire button to confirm. Press fire button to choose between TCR M 1, TCR M2. Press right/left buttons to select certain parameter. After setup is completed, press fire button to switch to “EXIT”. Press right or left button to confirm
7. Puff counter
In any mode, the screen shows the number of puffs. If a puff more than 0.8s, it will be recorded as one puff. The device can remember the value even if you remove the battery. The default number is “0000”. When the number is reaches “9999”, it will be cleared automatically.
9. Set the standby mode
Press the fire button 3 times in 2s to enter the menu, choose icon, use+ and -button to choose “Screen Time” area, there are 4 preset choices, press fire button to confirm your choice, the screen will enter standby mode at the selected time.
10. How to calibrate the resistance?
When the device connected with a new atomizer, press + and – button at the same time to calibrate the initial resistance of the new atomizer.
We recommend to calibrate resistance in temperature control mode , you can make the temperature control more accurate, please note that this operation requires heating wire cooling to room temperature.
11. Upgrade operation
After connecting the computer by USB & installation driver successfully , open the upgrade software, enter the correct PIO number, Open the program that needs to be upgraded on the PC and click the upgrade key of the upgrade software to upgrade. After update completed then work.
12. How to charge by USB?
When the voltage is lower than 3.3V, the display will show”Low Battery’; then you need to charge the device, please connect the device through the USB cable to the computer or power adapter.
1, in the charging process, The battery energy column indicator will scrolling,
when fully charged , it will stop scrolling.
2, in the charging process, the battery voltage is lower than 3.2V, the device
is turned off.
3, can not vape during charging
(If the device not be used for a long time, please charge every 30
to 60 days to make sure battery life.)
13.Malfunction
Indication and Protection
PCB temperature overheat protection When the temperature of device is too high, the output will shut off automatically and the screen will display “PCBTOO HOT”
Low power alert:
When battery voltage is below 3.2V, the device shows” LOW BATTERY”
PCB Atomizer short-circuit protection:
When atomizer short-circuit occurs, the OLEO screen will d1splay”SHORTED”
No Atomizer:
when no atomizer connect, the device will display “No atomizer”
Warnings
1. Please read the manual carefully before use
2. Please do not keep the e-juice inside the atomizer if the device is not going to be used for a long period
3. Please take out of the battery from device when it’s not used for a long time
4. Please keep the device away from children, pregnant women, and minors
(under 18 years of age)