Thank you for choosing IJOY! Please read this manual carefully to ensure
proper use. For additional information regarding this product or its use, please consult your local UOY retailer or visit our website www.ijoycig.com

Product Introduction:

The Elite Mini Kit is the evolution of IJOY RDTA Box mini platform,being capable offiring up to 60Wwith a built-in 2200mAh Li-Po battery while retaining the versatiIe foundationaI form factor. It is sleek and portabIe It is a new compact all-in-one kit that integrates three different vape styles into one chassis. Included with each kit is a IJOY RDTA Box mini mod, a IJOY Captain Elite SUBOHM&RTATankand a IJOY J& P Pod Adapter which extends ultimate flexibility in one device.
The Elite Mini Kit aims at providing ease of use, a rich flavor ecosystem and ultimate flexibility. It is a wonderful kit for entry level to enthusiast level vapers.

Parameter

1 * UOY BOX MINl(2200MAH) 1* USB Cable
1 * Manual      l*WarrantyCard

 

Specifications

• Screen size: 0.96″0LED.
• Size: 45*25*74 7mm /1.77*0.98*2.94 inches.
• Output Wattage: 5watts-60watts.
• OutputVoltage: lVolts-8.0Volts.
• Output Current: 1.0A-30A.
• Temperature Range: 300-600’F/ 150-31 S”C
• Wattage control mode wire Resistance Range: O.OSohm-3.0ohm
• Power efficiency: 95%.

• Fire method: Stainless steel metal stretch button.
• Adjust power method: up and down button.
• Upgradablefirmware:YES.
• Output mode·VW/TI/Nl/55 and special USER Mode
• Built-in Li-Po 2200 mAh battery
• Tank removable
• Big size filling hole

IJOY Elite Mini Kit Operation Instruction:

1. Power On/off

Press the fire button 5 times m quick succession to turn the device on and off. After switch on, OLED display BOX mini logo and software version number at stand by mode.

(Note:
Please adjust the wattage to a proper range to match the atomizer you used before using.

2.Vaping

While the device is power on,just keep pressing the fire button to vape
(Firing timeout: 10 Seconds)
While the device is power on, the OLED screen default display VW Mode.

3. General Functions

Enter Into The Main Menu
Press the fire button 3 times to enter into the
buttons to switch among different functions. Press the fire button to confirm.

4. Power Mode

In the main menu, switch to”P” setting, press fire button to confirm. Press right and left buttons to ad丿ust the wattage.
Intensity Setting In Power Mode
In the main menu, switch to intensity setting, press fire button to confirm Press right and left buttons to switch among below4 modes. In user mode, press fire button to switch among each setting columns. Press right and left

buttons to adjust the wattage After setup is completed, press fire button to switch to”EXIT”. Press right or left button to confirm.
Norm Mode: Maintains the currently set power.
Hard Mode: 30% higher than the currently set power.
Soft Mode: 20% lower than the currently set power.
User Mode. Customize the power output for the first three seconds of each puff, with each setting column representing half a second.

5. Temp Mode

Ni/Ti /55门CRM1/TCRM2
In the main menu, switch to·T”setting, press fire button to confirm. Press right and left buttons to switch among Ni/Ti/SS/Ml/M2 modes. Press fire button to confirm. Press right button, when “W”flashing, press right and left buttons to ad丿ust wattage. Press left button, when”°F” or”0C”flashing, press right and left buttons to ad丿ust temperature value.

The temperature unit will cycle between ° F and °C when the minimum or maximum temperature is reached.

In the temperature control mode to replace the heating wire, when the new heating wire resistance and the previous heating wire resistance difference greater than or equal to 0.2ohm, the screen appears the following tips. Press+ to choose and confirm new coil. Press -to choose and confirm same coil.

 

6. TCR Mode (M1, M2)

With theTCR (Temperature Coefficient of Resistance) function available now, you can customize your temperature control coils(Ni, Ti, 55) on your own In the main menu, switch to”T飞etting, press fire button to confirm. Switch to Ml /M2 modes. Press fire button to confirm.

How to set the TCR?

In the main menu, switch to”TCR” mode indication, press fire button to confirm. Press fire button to choose between TCR Ml, TCR M2. Press right/left buttons to select certain parameter. After setup is completed, press fire button to switch to”EXIT”. Press right or left button to confirm.

7. Puff counter

In any mode, the screen shows the number of puffs. If a puff more than 0.8s, it will be recorded as one puff. The device can remember the value even if you remove the battery. the default number is”OOO”. When the number reaches “999′; it will be cleared automatically.

How to clear the puff value manually?

Press the fire button 3times in 2s to enter the menu,
choose to enter the’PUFF rest’setting, press fire button to confirm your choice.

8. Set the POD Mode:

Press the fire button 3 times in 2s to enter the menu,
Select  icon to POD Mode. Please adjust wattage in the range of 5-12W in this mode.

9. Set the standby mode

Press the fire button 3 times in 2s to enter the menu,
choose    icon, use+ and – button to choose Screen Time area, there are 4 preset choices, press fire button to confirm your choice, the screen ewill enter standby mode at the selected time.

10. How to calibrate the resistance?

When the device connected with a new atomizer, press+ and – button at the same time to calibrate the initial resistance of the new atomizer.
We recommend to calibrate resistance in temperature control mode , you can make the temperature control more accurate, please note that this operation requires heating wire cooling to room temperature.

11. Upgrade operation

Connect the device to a computer via a USB cable, press+ and – button together and press fire button at the same time to enter the upgrade process. Then release the+ and – button first, release the fire button later, Upload the latest firmware, unt仆 the upgrade operation is completed, press the+ and – button to reset, the device can work properly.

12. How to charge by USB?

When the voltage is lower than 3.3V, the display will show”Low Battery’; then you need to charge the device, please connect the device through the USB cable to the computer or power adapter.
1, in the charging process, the red light is bright, full power will go out
2, in the charging process, the battery voltage is lower than 3.2V, the device
is turned off.
3, can not vape during charging
(If the device not be used for a long time, please charge every 30 to 60 days to make sure battery life.)

13.Malfunction

Indication and Protection
PCBtempe『ature overheat protection. When the temperature of device is too high, the output will shut off automatically and the screen will display”PCB TOO HOT”

Low power alert:


When battery voltage is below 3.2V, the device shows” LOW BATTERY”

PCB Atomizer short-
circuit protection:


When atomizer short-circuit occurs, the OLED screen will display”SHORTED”

No Atomizer:


when no atomizer connect,the device will display”No atomizer”

Low resistance protection:


When the resistance is lower than 0.06ohm, the OLED screen will display”OHMS TOO LOW”.

When the resistance is higher than 3ohm, the OLED screen will display”OHMS TOO HIGH”.

 

Warnings

1. Please read the manual carefully before use
2. Please do not keep the e-juice inside the atomizer if the device is not going to be used for a long period
3. Please take out of the battery from device when it’s not used for a long time
4. Please keep the device away from children, pregnant women, and minors
(under 1 Byears of age)

Related posts
Thank you for choosing UOY! Please read this manual carefully to ensure proper use. For additional information...
Thank you for choosing IJOY! Please read this manual carefully to ensure proper use. For additional information...
IJOY has been hotting in the vape market for a long time. You can see that their new products are launched...
Steam Crave Hadron Mini DNA100C Combo Kit is a high-end and powerful device capable of providingvarious...

Sharing is caring!