INSTRUCTIONS

1. Inserting battery cell: The device flash “Geok vapor” one time and then screens out when you inset battery cell,

2. Power On: Press the fire button 5 times within. seconds to power on, The device will display the startup animation and enter the standby interface. Power off Press the fire button times within2 seconds to power off. The device will display the shutdown animation,

3. Power adjustment: In the Power adjustment mode, press theβ€œ+” or”.” button to adjust the power, the increment is 0.5W when the power is less than 100w, and the increment is 1W when the power is greater than 100W, toggle between 5 200W, and long pressing and holding the button to enter the quick adjustment mode.

4. Temperature control mode: In the Temperature control mode, press the”t” or “,” button to adjust the temperature. The increment is 5F/1C each time, toggle between 100C -315C or 200 P ~600 T, and long pressing and holding the button to enter the quick adjustment mode.
When the present temperature model has been adjusted to the maximum minimum value, pressing the button once again, the Fahrenheit and celsius units will be switched automatically at the same time.

5. Setting mode: Press the Fire button 3 times in quick succession to enter the setting mode.

6. Exiting setting mode: Long press the Fire button for 0.8s to exit the setting mode (The device will automatically exit the setting mode after 5s without operation),

7. Switch operation mode: Press the Fire button 3 times in quick succession to enter the setting mode.
When the cursor stays in working mode in the upper left corner, press the”+” or”-” button to adjust the corresponding setting item.
Optional work modes include POWER. NI TI, Ss. TCR. VPC, BYPASS.

8. Setting the wattage: Press the Fire button 3 times in quick succession to enter the setting mode,
Press the Fire button to toggle the cursor and select the WAT,
Press the “+” or”.” button to adjust the WAT parameters, and long press the button to enter the quick adjustment mode.

9. Reset the puff: Press the Fire button 3 times in quick succession to enter the setting mode.
Press the Fire button to toggle the cursor and select the PUFF;
Press the”+” or”-“‘ button to clear the current value;
Press the “+” or “-.” button again to recover the current value;

10. Change VPC parameters: Press the Fire button 3 times in quick succession to enter the setting mode.
Press the Fire button to toggle the cursor and select the TCR;
Press the”+” or”-” button to adjust the TCR parameters, and long press the button to enter the quick adjustment mode.

11. Change VPC parameters: Press the Fire button 3 times in quick succession to enter the setting mode.
Press the Fire button to toggle the cursor to P1;
Press the “+” or-,” button to adjust the Pl power value, and long press the button to enter the quick adjustment mode.
Continue to press the Fire button to toggle the cursor to the P2;
Press the “+” or-” button to adjust the P2 power value, long press the button to enter the quick adjustment mode.
Repeat the same operation to adjust the P3, P4, and P5 power values.

12. Prompts: Anti-reverse battery protection. (Reverse battery connection does not damage chip)
While the resistance of tank <=0.08ohm, the device prompts short circuit for 2s.While the resistance of the tank >=3.5ohm, the device prompts high resistancefor2s.
Single battery voltage < 3.2v before use or <2.8v during use, the device will stop output automatically and prompt low voltage for 2s. When the temperature of the circuit board >65 c before use or>85C during use, the device prompts high temperature for 2s.
No atomizer: press the fire button, and the device prompts no atomizer for 2s.The single output is over 10s timeout, the device stops output and prompts timeout for 2s.
In the locked state, press the “+” or “-” button to adjust the parameters, the device prompts screen lock for 2s.

13. Resistance lock: When the cursor is a toggle to the resistance value of coil, press the “-” button to lock/unlock the resistance value, and press the “-button to update resistance value and unlock.

14. New atomizer: In the standby interface, it will monitor whether the atomizer is replaced and update the latest atomizer resistance.
When a new atomizer is inserted, the screen will jump to the interface for selecting new and old atomizers and prompt the user to select new and old atomizer.
Click the ‘+’ key to select the new atomizer, and click the ‘ key to select the old atomizer.
When the original atomizer is removed, the resistance value will be automatically cleared.

15. Version information display: Press the fire button 5 times in quick succession to turn off the device, press the “+”and-” buttons simultaneously for 2 seconds, and the screen displays the version information of the current system and the latest time of upgrade.

Aegis Legend 2 Classic Kit
GV20200918 V10
Version information display;
Aegis Legend 2 Classic Kit
GV20200918 V10
(20200918V10is the update time and version of the software, GVis Geek vape, please contact me for the supplier code and USB version number to prevent version conflicts and user upgrade failures)

16. Configuration Reset: After entering the version information interface, press and hold the “Fire”, “+” and “-” buttons simultaneously for 2s to restore factory settings, the screen prompts to restore the factory interface, the user releases the buttons for 2S to exit the prompt interface.17. Stealth mode: Press the Fire button, “+” button and-” button simultaneously for 2s, entering Stealth mode.
Do the same, and exit the stealth mode,

17. Switch display style: On the setting mode, press the’+’ and- buttons simultaneously for 1s to switch to the next theme.

18. Screen brightness adjustment: In the standby interface, press and hold the fire key and the ‘+’ key for 1 second at the same time to display the brightness adjustment icon and turn the screen brightness step by step. Press and hold the fire key and ‘- key at the same time to dim the screen brightness,

19. Using while recharging: Normal charging process and the ignition condition is satisfied, press the Fire button, charging is suspended, ignition output.
Normal charging is restored after the ignition output is finished.

20. Upgrade: The user terminal can upgrade, to USB HID mode.

Related posts
INSTRUCTIONS 1. Power-on: Display power-on animation after installing battery, then the display...
Thank you for choosing GEEKVAPE Please read the user manual before using this product for better user...
How to Use IJOY Captain PD270? How to power IJOY Captain PD270 on/ off? Press the fire button 5 times...
We believe that everyone is very familiar with Vapefly Kriemhild Kit. It is a limited edition of...

Sharing is caring!