The device “Geekvape Aegis Legend Kit” is water and dust resistant and was tested under conditioned.
Laboratory conditions with a rating of IP67. Water and dust resistance are not permanent conditions and resistance as result of normal wear. Do not attempt to charge in wet condition. Liquid damage not covered under warranty.

Thank you for choosing GEEKVAPE

*Please read the user manual before using this product for better user experience.
*Keep the user manual for future reference.

Overview

Aegis Legend Kit 1

Aegis legend Kit Product Feature

 

Advanced AS chipset powers up to 200W with colored display screen.
IP67 water resistant, able to withstand immersion for up 30 minutes at a depth of up to 1 meter.
Shock resistant , able to withstand natural drop from up to 2 meter high.
Dual 18650 battery compatible.
Dust resistant (IP67), able to withstand dirty environment and can be easily cleaned.

Product Parameters

Max power out :200W
Output mode: Adjustable output
Shell material: Aluminum + Zinc alloy + Silicone
Physical dimension: 30.60*58.60*90.30mm
Battery capacity: External
Shell color: Black
Charging specifications: 5V 1A
Battery low voltage warning: 6.6V±0.1V
PCBA temperature alarm: 85 ℃
Max single output duration: 10s
Maximum voltage output: 9V±0.1V
Operating temperature: 0~40℃

Contents

1.* Aegis legend Kit 1*User manual 1* 0.15 ohm coil head
1* USB Cable 1* Spare silica glass 1*Spare parts pack

Aegis Legend Kit 2
Instructions

1. Turn On: Press the fire button 5 times in quick succession to turn On the device. 2.Turn Off: Press the fire button 5 times in quick succession to turn OFF the device.
3. Mode Selection: Press the fire button 3 times in quick succession to enter the mode selection screen.
4. Switch between working modes: In the mode selection screen, use the + & – button to toggle between the modes and press and hold the fire button for 0.8s for allow 5s of inactivity to select.
5. TCR Mode: On the mode selection screen toggle to TC-TCR, press and hold the fire button to enter the mode, use + & – button to adjust the TCR value.
6. VPC Mode: On the mode selection screen toggle to VPC, press and hold the fire button to enter the VPC mode. Press the Fire button and use the + & – button to set the values of P1/P2/P3/P4/P5.
7. Resistance and Puffs reset: Enter the setting state. Press the Fire button to toggle the cursor to the COIL or PUFF. Press + to reset the COIL or PUFF value.
8. Screen lock: Press the + & – button simultaneously to lock and unlock the screen.
9. Display brightness adjustment: Press and hold the Fire & + or – button simultaneously to adjust the brightness of the display.
10. Stealth mode: Press the Fire, the ‘+’ and the ‘-’ keys simultaneously for 2 seconds to enter the Stealth mode. The same operation to exit stealth mode. In Stealth mode, you can only vape or shut down.
11.USB upgrade: Remove the atomizer and battery, press and hold ”+” key while inserting in the USB to a PC, perform an upgrade on the PC using the Geekvape firmware upgrade software.

Aegis Legend Kit 3
12.USB Charging: Connect USB to a power source to charge batteries, battery icon will begin to animate and stop once fully charged.
13.Display Colors: In mode selection screen, press the “+” and “-” keys simultaneously for 1 second to switch between display colors.

Description of Warning

1.NO COIL DETECRED: No atomizer detected. Please check if the atomizer and coil is properly connected.
2.PROTRCTION ATOMIZER SHORT: The atomizer is short circuited. Please check your coil for any shortage.
3.ATOMIZER RESISTENCE HIGH: Resistance of the atomizer is too high. Please check your coils.
4.10s CUT-OFF PRETECTION: Output will automatically shut off after 10s.
5.BATTERY LOW PROTECTION: Battery voltage is low, please recharge your battery.
6.BATTERY WEAK PLZ LOWER WATTAGE: The battery is too weak, please check whether it is well connected / replace with a higher rated battery / lower the power setting or charge your battery.
7.UNLOCK PRESS + & – : Press the (+) & (-) button simultaneously to Unlock.
8.DECIVE OVERHEAT PRETECTION: Temperature of the PCB is over 85℃, Please allow the device to cool down.

COSTOMER SERVICE
ATTENTION

Product is not intended for use by pregnant women and children under the age of 18
Keep away from fire
Avoid impact

Service in China
Website: www.geekvape.com
ADD: Xingye Rd. #3012, Ban’an District, Shenzhen, China
Email: support@geekvape.com
Available: Mon-Fri, 9AM to 6PM CST

Service in the USA
Website: www.geekvape.com
ADD: 637 E Big beaver Rd STE 211, Troy, Michigan, 48083 USA
Phone: 866-477-4335
Email:service@geekvapeusa.com
Available: Mon-Fri, 9AM to 6PM EST

ANTI-COUNTERFEITING QUERY
VISUAL METHOD

① Sway the label under light lightly
② Logo will expand gradually to curved shape with the different viewing angle.

WEBSITE AUTHRNTINITY CHECK

① Go to www.geekvape.com and scroll right to the bottom of the main page.
② Scratch the code and enter the 12 digit security numbers on the blank field.
③ Click on the “Go” button and a pop up window should appear confirming. If your product is authentic.

 

You may want to know:

No Coil Detected – GeekVape Aegis Legend 200W

Geekvape Firmware Upgrade Tool Download

 

Geekvape User Manual:

How to Use Geekvape Aegis Legend Kit – User Manual

How to Use Geekvape Aegis Mini Mod – User Manual

How to Use Geekvape Nova Kit – User Manual

 

Related posts
Aegis legend Kit is a waterproof, dust-proof, and drop-resistant vape kit introduced by Geekvape. Most...
Have you ever dropped your mobile phone into the water? After this situation occurring, you must feel...
Thank you for choosing Geekvape Product Please read user manual before using this product for better...
Thank you for choosing Geekvape Product Please read user manual before using this product for better...

Sharing is caring!

Comments

    1. What do you mean? when your coil has a resistance below 0.16 ohm, your machine won’t work? 1. Check if your wire material is suitable. 2. Switch output mode to try.

      1. I’m having a similar problem, when I try to change the ohm temp it shows that it’s locked. Not the whole screen, just next to 0.18 (my current ohm)

  1. I’m having a similar problem, when I try to change the ohm temp it shows that it’s locked. Not the whole screen, just next to 0.18 (my current ohm)

  2. A newbie here.. First vape.. my aegis 200w has stop charging. Only had it 2 weeks. Charging it with cord that came with it. I have a Mac no windows so I can’t do any kind of updates. Same batteries that came with it. I’m sure it’s an easy fix but I have no clue what I’m doing. It’s to late to go get cigs please help b4 punch myself in the face for paying this much for something that breaks 2 weeks later.

    1. Hi,brandy! Have you tried charging your battery with an external charger? Here are three reasons for the problem: 1. Your battery is broken 2. Your device is broken 3. Your charging cable is damaged. If you still haven’t solved your problem, you can contact GeekVape. Thank you

  3. Can you tell me why on every picture I have seen of my mod there is a number displayed for the amp, I believe at one time I had some kind of number there for mine too however my settings seem to be good with the exception of that? Is it a setting I have to fix or is it normal?

Leave a Reply

Your email address will not be published. Required fields are marked *