Thank you for choosing Geekvape
Please read the user manual before using this product for better experience.
Keep the user manual for future reference
Overview
Setup guide
1. Get the product
2. Pull off the top cap
3. Build your coil
4. Prime with e-liquid
5. Place back the top cap
Product Parameter
Rated voltage: 6.2-8.4V
Rated power output: 5.0~200W
Maximum voltage output: 8.0V±0.1V
Chasis material: (ABS+PC) + Zinc Alloy
Physical dimension: 114.9*55.7*46mm
Standby current: Quiescent current (shutdown mode)
≤100uA Standby current (no load) ≤ 25mA
Power output mode: Adjustable output
Resistance read range: 0.05-3ohm
Resistance read accuracy: 0.02ohm
Battery low voltage warning: 6.6V±0.1V
PCBA temperature warning: 85℃
Rated resistance: 0.1-3ohm
Maximum output duration: 10s
Battery requirement: Dual 18650 Lithium battery
Operating temperature range: -10~ 40℃
Full charge voltage:4.15V±0.0145V
Charger requirement: 5V 2A
Airflow intake: Side airflow
Coils: DIY
Resistance: DIY
Filling method: Top drip
Contents
1 * GBOX Mod + Radar RDA 1 * Spare Squonk bottle
1 * Radar RDA Accessories pack 1 * GV Allen key
1 * Delrin drip tip 1* 510 drip tip adapter
1 * USB cable 1 * User manual
Product Specifications
Instructions
1. Turn on: Press the fire button 5 times in quick succession to turn on the device.
2. Turn off: Press the fire button 5 times in quick succession to turn off the device
3. Setting state: Press the fire button 3 times in quick succession to enter the Setting state.
4. Switch between working modes: (POWER/TC-NI/TC-SS/TC-TI/TC-TCR/VPC/BYPASS) In the setting state use the (+)&(-) button to toggle between modes, press and hold the fire button for 0.8s or allow 5s of inactivity to select.
5. TCR Set up: On the mode selection screen toggle to TC-TCR, press and hold the fire button to enter the mode. Use the (+) & (-) button to adjust the TCR value.
6. VPC Set up: On the mode selection screen toggle to VPC, press and hold the fire button to enter the VPC mode. Press the fire button and use the (+) & (-) button to select the values to P1/P2/P3/P3/P4/P5.
7. Resistance and Puff Reset: Enter the setting state. Press the fire button to toggle the cursor to the coil or puff. Press (+) to reset the coil or puff value.
8. Resistance Lock: Enter the setting state. Press the fire button to toggle the cursor to the coil. Press (-) button to lock and unlock the resistance.
9. Screen Lock: Press and hold (+) & (-) botton simultanrously to lock or unlick the screen.
10. Display Brightness Adjustment: Press and hold the fire & (+) or (-) button simultaneously to adjust the brightness of the display.
Warning Descriptions:
1. No Coil Detected: No atomizer detected. Please check if the atomizer and coil is properly connected.
2. Protection Atomizer Short: This atomizer short circuited. Please check your coils for any shortage.
3. Atomizer Resistance High: Resistance of the atomizer is too high. Please check your coils.
4. 10s Cut-Off Protection: Output will automatically shut off after 10s.
5. Battery Low Protection: Battery voltage is low, please recharge your battery.
6. Battery Weak PLZ Low Wattage: The battery is too weak, please check whether it is well connected / replace with a higher rated battery / lower the power setting or charge your battery.
7. Unlock Press + & -: Press the (+) & (-) button simultaneously to Unlock.
8. Device overheat protection: Temperature of the PCB is over 75℃, please allow the device to cool down.
9. No Liquid: Atomizer is dry, please add liquid.
10. New +: 0.00Ω Same- :When the NEW or OLD atomizer display occurs on TC mode, press (+) button to re-detect the resistance, press (-) button to select the previous resistance.
Customer Service
Attention
Product in not intended for use by pregnant women and children under the age of 18
Keep away from fire
Avoid impact
Service in China
Main page:www.geekvape.com
Add: Xingye Rd. #3012, Bao’an District, Shenzhen, China
Email: support@geekvape.com
Available: Mod-Fri, 9AM to 6PM CST
Service in the USA
Main page: www.geekvapeusa.com
Add: 637 E Big beaver Rd STE 211, Troy, Micigan, 48083 USA
Phone: 866-4335
Email:service@geekvapeusa.com
Available: Mon-Fri, 9AM to 5pm EST
ANTI-COUNTERFEITING QUERY
Visual Method
1. Sway the label under light lightly
2. Logo will expand gradually to curved shape with the different viewing angle
Website authenticity check
1. Go to www.geekvape.com and scroll right to the bottom of the main page.
2. Scratch the code and enter the 12 digit security numbers on the blank field.
3. Click on the “Go” Button and a pop up window should appear confirming if your product is authentic.
Geekvape User Manual：
How to Use Geekvape Aegis Legend Kit – User Manual
How to Use Geekvape Aegis Mini Mod – User Manual
How to Use Geekvape Nova Kit – User Manual
How to Use Geekvape Athena Kit – User Manual
How to Use Geekvape Blade Kit – User Manual
How to Use Geekvape GBOX Squonk Kit – User Manual
How to Use Geekvape Tsunami Mesh Kit – User Manual
How to Use Geekvape Mesh Pro Kit – User Manual
How to Use Geekvape Alpha Sub-Ohm Tank – User Manual
How to Use Geekvape Loop RDA 1.5 – User Manual
Related posts
